High duty cycle due to additional fan function. 328 | ELECTRODE WELDING SYSTEMS COMMON FEATURES .. "Smart intelligence": state-of-the-art processor control for easy operation and ideal welding results .. Automatic hot start for perfect ignition of electric arc .. Arc-force regulation for even welding results .. Anti-stick mechanism prevents electrodes from sticking .. Switchable lift arc function for x-ray safe TIG welding with an optional TIG torch .. Ergonomic and protected control elements ..

Si l’on vis vers l’exterieur, on diminue la quantite qui circule. x Lors du reglage, il faut mettre l’appareil en service et l’interrupteur du chalumeau doit etre pousse pour pouvoir ouvrir la vanne magnetique. Pour eviter de consommer trop d’electrode, on fait pivoter lateralement le ressort a lames de l’avancement d’electrode. Les operations et reparations sur les detendeurs sont interdits, a cause des dangers que representent ces operations. Les detendeurs qui sont defectueux doivent etre exp

x Neighbouring workplaces are to be screened off to provide protection against radiation. x When welding inside rooms and buildings sufficient ventilation must be ensured. A A Fire Danger! The arc temperature is approx. 2400 °C. Before starting to weld observe the following information: x Remove all combustible materials and objects within a radius of 5 m from the welding point. x Materials that can not be removed within a 5 m radius must be protected by covering with sheet metal, wet cloths etc

B. Work Practice Controls: involve adjustments in the way a task is performed, as well as the periodic inspection and maintenance of engineering control equipment. In many cases, work practice controls complement engineering controls in providing employee protection. C. Personal Protection Equipment: When engineering and work practice controls cannot reduce employee exposure to within the PEL, employers must provide respirators. OSHA’s Methods of Compliance states that: "If feasible engineering

See Figure 7. Of these, the Butt Weld and Fillet Weld are the two most common welds. Butt weldLap weldEdge weldFillet weldCorner weld FIGURE 7 Para el Proceso FCAW (Innershield) 1. .Necesito que sea sencillo y facil de transportar? 2. .La soldadura se va a realizar en exteriores o bajo condiciones de viento? 3. .Requiero una capacidad de soldadura adecuada en todas las posiciones? 4. .La mayoria de la soldadura se realizara en calibre 16 o mayor, asi como en materiales oxidados o sucios? 5. La s

Vantage 500 DEUTZ C-1 ACCESSORIES C-1 OPTIONAL FIELD INSTALLED ACCESSORIES K704 ACCESSORY SET - Includes 35 feet (10 m) of electrode cable and 30 feet (9 m) of work cable, headshield, work clamp and electrode holder. Cable is rated at 500 amps, 60% duty cycle. K767-2 FOUR WHEELED STEERABLE YARD TRAILER - For in plant and yard towing. K802N POWER PLUG KIT - Provides four 120V plugs rated at 20 amps each and one dual voltage, full KVA plug rated at 120/240V, 50 amps. 120V plug may not be compatibl

Clair Avenue Cleveland, OH 44117-1199 (216) 481-8100 Product Type: Cored Electrode Classification: None SECTION II - HAZARDOUS MATERIAL (1) I M P O R T A N T ! This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal use of this product are covered by Section V; see it for industrial hygiene information. CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all size

UU 4338BA013 KN Choke 5 : Coloque la palanca del estrangulador ( 4): en g si el motor esta frio en esi el motor esta tibio (aunque el motor haya estado funcionando pero todavia este frio) en fsi el motor esta caliente (posicion trabada para arranque tibio) : Presione el boton para abrir la valvula de descompresion ( 5). Es necesario oprimir el boton antes de cada intento de arranque del motor. START 338BA014 KN 338BA015 : Coloque la sierra sobre el suelo, mantenga buen equilibrio y asegurese que

5 year warranty on main transformer .. CE-inspected Comparative device characteristics Mains voltage 230/400 V 230/400 V Maximum power input at 400 V 6,7 kVA 6,7 kVA Setting range (400 V) 60 - 170 A 60 - 170 A Regulation 6 levels each 6 levels each Weldable wire 0,6 - 0,8 mm 0,6 - 0,8 mm Weldable material thickness 0,5 - 6 mm 0,5 - 6 mm Maximum duty cycle at 25 °C 30 % 30 % Maximum duty cycle at 40 °C 20 % 20 % 100% duty cycle at 25 °C 90 A 90 A 100% duty cycle at 40 °C 60 A 60 A Fuse protection

SQUARE WAVE TIG 255 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOCReturn to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC F-7 TROUBLESHOOTING & REPAIR Observe Safety Guidelines TROUBLESHOOTING GUIDE detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION FUNCTION PROBLEMS The yellow light (PL1) on the front panel is not lit. 1. Normal condition - this light w