• Allow 25-30 minutes for the briquettes to light before cooking, The briquettes should have a light coating of ash on top of them when ready. • When using lighter fluid allow ample time for liquid to soak into briquettes before lighting, light briquettes in several places to ensure maximum ignition. • Store your charcoal in a dry place. If storing outside, seal charcoal in a waterproof container. • Diatomite grill is frangible. Be careful of the grill when attempt to store and remove it. • When

Distributed by: Well Traveled Living P.O. Box 4 Amelia Island, FL32035 Tel: 866-985-7877 Fax: 904-261-6769 1 INTRODUCTION • Use only in a well ventilated area. • This appliance must only be used outdoors. • Do not use under canopies or awnings. • Do not move the appliance while it is lit. • For spare parts and servicing contact 866-985-7877 or cservice@welltraveled.net. The Chopping board must be stored inside! Safety instructions FOR YOUR SAFETY: 1 Read the assembly instructions carefully. See

For warranty service contact Well Traveled Living at the address, phone numbers or internet site and email listed in this owner’s manual. Be sure to have your sales receipt, date of purchase and catalogue/model numbers available when calling. All warranty service will be coordinated by the Well Traveled Living’s, Amelia Island, Florida service center. This warranty is extended only to the original purchaser. Proof of purchase will be required before warranty service is rendered. The sales receip

Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging. For warranty service contact Well Traveled Living at the address, phone numbers or internet site and email listed in this owners manual. Be sure to have your sales receipt, date of purchase and catalogue/model numbers available when calling. All warranty service will be coordinated by the Well Traveled Livings, Amelia Island, Florida service center. This warranty is extended only

Disconnected cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area. -4- ASSEMBLY 1. 3 pcs castle nuts 2. Reflector 3. 6 pcs 8mm washers for pins support 4. 3 pcs 90mm (L) pins for reflector support 5. Head assembly 6. 4 pcs M6xl0mm bolts 7. 2 pcs Post assembly 8. Tank housing 9. Regulator 10. 6 pcs M6x30mm bolts and 6mm nuts for connection of post support and support legs 11. 3 pcs M8xl6mm bolts for connec

Please see page 9 "Check for Leak" for full instructions. 7-3. Put gas cylinder on the stand. rest it on of gas hose as cylinder and Ln ASSEMBLY 7-4. Lower tank over gas cylinder and down to cover base. Check for Leak Your patio heater has been checked at all factory connections for leaks, but you should always check when you attach the LPG cylinder. To check for leaks, follow these instructions: --Assemble all gas connections; --Connect regulator assembly to the propane tank; --Make

Both smoke and odor will dissipate after approximately 30 minutes. The heater should not produce thick black smoke. Note: The burner maybe be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the “LOW” position, then turn the knob to the level of heat desired. Warning : White smoke may appear around the radiant head during the first minutes of the initial firing. When heater is ON: Emitter screen will become bright red due to intense heat. The

Disconnected cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage, or any other enclosed area. . - 4 ASSEMBLY PARTS LIST 1. Burner assembly 2. 4 pcs mesh guard 3. Handle with 2 pcs M6 nuts and 2 pcs flat gaskets 4. Back panel 5. 5 pcs M4x10mm bolts, 5 pcs M4 flat gaskets, and 5 pcs M4 nuts to connect the burner assembly with back panel 6. Regulator with gas hose 7. Door panel 8. 10 pcs M5x12mm bolts and 10pcs M5 nuts for connection of 5 bracket

Oils from your hand could reduce the life of the lamp by causing a heat spot. Recommend using clean cotton or plastic gloves. A clean paper towel may also work. Quartz Halogen Lamp Replacement: * Be sure unit is unplugged from wall outlet! * Remove head unit assembly from wall mounting bracket (refer to step 3 from page 5) * Remove 8 screws from each end of the head unit and pull off end plates (see #2) - Note the placement of the 2 small sheet metal screws on each end plate. Also, note en

Tighten securely. *** IMPORTANT NOTE: be sure to route and keep the electrical cord AWAY from the main body of the heater unit. *** FigT3 Min. Clearances: 83” head unit height 10” from mounting wall 12” from surfaces above the heater head unit 36” from sides and front of head unit 45-55 degree angle of operational spread Route power cord below and away from head unit as show in box 5. ///?*?*//. Correct v/ ///?*’// Wrong Wrong to lock position of head unit. Page 5 *** Important No