WORKING CIRCUMSTANCE 1. To reduce the risk of injury associated with exhaust fume inhalat i o n , d o n o t o p e r a t e i n unventilated area. The exhaust gases contain harmful carbon monoxide. 2. Avoid using the blower where stable footing and balance are not assured. 3. Never operate the machine in high wind, bad weather, potentially explosive atmosphere, when visibility is poor or in very high or low temperatures. (Our recommended use environment is below 40 degrees C (104 degrees F).) AVOI

(OP2) 7. Allow the engine to warm up for a several minutes before starting operation. 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. NOTE IMPORTANT WARNING 8. Operation OP1 (1) (2) (3) OP2 (4) (7) (5) (6) OP3 OP4 NOTE IMPORTANT WARNING 8. Operation OP1 (1) (

2. KOMATSU ZENOAH does not warrant the machines, those which have been damaged by the use of any parts other than those specified by the company. 3. When placing orders of parts for repair and/or replacement, check if the model name and the serial number are suitable to those specified in the parts list, then use parts number described in the parts list. 4. The contents described in the parts list may change due to improvement. 5. The parts for the machine shall be supplied within ten (10) years

This unique mechanism brings you many benefits like the following: 1. Since the blade does not cause grass chips and pebbles to the thrown around, you may use less care about your clothing or surroundings. 2. Should the blade hit a rigid object like stones, trees or steel poles during operation, it does not produce a bounce motion that can cause loss of machine control. 3. Since the blade does not cause cut grass to wrap around the neck, you need not to stop operation to remove such wrappers. Wh

Pay attention to agitation. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. GB-9 SGCZ2600DL/SGCZ2600DW 8. Operation STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflow

Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. IMPORTANT • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and G damaged. B •To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. 87 ~ 104 in-lbs TIGHTENING

(MA5) (1) Parachispas ¦ TOMA DE AIRE DE REFRIGERACION ADVERTENCIA • Nunca toque el cilindro, el silenciador o las bujias con las manos descubiertas inmediatamente despues de parar el motor. El motor puede alcanzar altas temperaturas mientras funciona, por lo que tal accion podria causarle graves quemaduras. • Al comprobar la maquina para asegurarse de que esta bien antes de usarla, compruebe la zona alrededor del silenciador y quite todas las astillas de madera o las hojas que se hayan adherido

The engine can become very hot when in operation, and doing so could result in severe burns. •When checking the machine to make sure that it is okay before using it, check the area around the muffler and remove any wood chips or leaves which have attached themselves to the machine. Failing to do so could cause the muffler to become overheated, and that this in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste