NOTE: Various combinations of legs and spacers are available for Model 0482 airpot brewer. The total combination of legs and spacers must be equal for all four corners. Set Brewer in its operating location. Level the Brewer. A spirit level should be placed on the top of the unit, at the edge, as a guide when making level adjustments. Level the unit from left to right and front to back by turning the adjustable feet. Be sure all four feet touch the counter to prevent tipping. IMPORTANT: To enable

2 Water Supply Installation INSTALLATION (continued) INSTALLATION (continued) WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brewer or result in decreased performance. Such damage is not covered by warranty. IMPORTANT: Do not conne

Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove decanters or airpot. 3. Remove and empty brew chamber. 4. Remove the spray disk from the brew head (See figure 8): Press up on the spray disk ears, then turn the disk to the left to unlatch. Remove the gasket from inside the brew head. 5. Wipe inside of brew head and area around the brew head with a soft clean cloth or sponge moistened with clean water. 6. Wash the spray disk in a sink using warm water and a m

12 685 77110 Owners Manual Horizon™ Brewers 685 77110 Owners Manual Horizon™ Brewers SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Disconnect brewer from electric power. Remove top panel. Remove button plug from front panel. Pull vent tube out of tank lid and insert a thermometer of known accuracy in hole. Reconnect brewer to electrical power. Place empty container under brew chamber. Energize brewer and allow unit to heat. When READY light glows, read the temperature displayed on th

airpots carry a 30 day parts warranty only. b. dispensers; i.e., tea and coffee carry a 90 days parts warranty only, excludes decanters. THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED. BLOOMFIELD INDUSTRIES DIVISION / SPECIALTY EQUIPMENT MANUFACTURING CORPORATION SHALL NOT BE LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES O

Remove top cover and detach solenoid access door from cabinet. Remove faucet tube from faucet valve at flare fitting. Remove water supply flare fitting: a. Slide the 5/8" end of the wrench over the flats on the inlet fitting of the valve. b. Hold the wrench to prevent the inlet fitting from turning while installing or removing the inlet water supply flare nut. Remove faucet tube from solenoid: a. Slide the 7/16" end of the wrench between the valve body and the white ring on the extreme end of th

This manual contains the information needed to properly install this appliance, and to use, care for and maintain or repair the appliance in a manner which will ensure its optimum performance. WARRANTY STATEMENT xi SPECIFICATIONS 1 FEATURES & OPERATING CONTROLS 2 PRECAUTIONS & GENERAL INFORMATION 3 AGENCY LISTING INFORMATION 3 INSTALLATION INSTRUCTIONS 4 OPERATION 6 BREWING COFFEE 10 CLEANING INSTRUCTIONS 11 TROUBLESHOOTING SUGGESTIONS 12 SERVICING INSTRUCTIONS 14 Deliming Instructions 20 EXPLOD

Press the ON/OFF key again to turn the brewer OFF. Three beeps will sound, the tank heater and all warmers will be switched off, and all indicator lights will go out. Brew Settings See pages 17 & 18 for setting Brew Time and Temperature. ABS™ (Automatic Brew Start) Start a brew by pressing BREW. A single beep will sound. The system will verify that the water in the tank is at the proper temperature. If it is, brew will start immediately. Otherwise, the BREW indicator will flash (Brew Waiting Mod

Possible causes of Over Temperature condition: • Setpoint is in the boiling range. • Heating element or temperature probe has malfunctioned. • Excessive scale buildup is preventing the element from heating the water. • Heating element relay fails in the “on” state. • No water in the tank. • Hi-limit safety tripped (must be manually reset) To reset the brewer: • Determine the cause of the failure and take appropriate remedial action to rectify the problem. • Press and hold the CANCEL key for thre