4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

The grounding wire has insulation with an outer surface that is green - with or without yellow stripes. If these grounding instructions are not completely understood, or if in doubt as to whether the compres sor is properly grounded, have the installation checked by a qualified electrician. 120 Volts, 15 Amps 120 Volt Models Air Hose The air hose attached to your compressor has an integral pressure adjusting valve at the working end of the hose. Should service or replacement be required, make su

TECNICAS DE LIMPIEZA Cuando se procede a la limpieza con la hidrolimpiadora, se pueden efectuar diferentes operaciones solo con el agua; en muchos casos, sin embargo, es conveniente utilizar tambien un detergente. El uso de un detergente asegura un tratamiento inmediato de la suciedad, permitiendo al agua con alta presion penetrar y eliminar eficazmente la suciedad. La posicion de baja presion suministra una aplicacion delicada del producto quimico. Recomendamos esta posicion tambien para enjuag

Dicha informacion se relaciona con la proteccion de SU SEGURIDAD Y LA PREVENCION DE PROBLEMAS AL EQUIPO. Para ayudarlo a reconocer esa informacion, utilizamos los simbolos indicados mas abajo. Sirvase leer el manual y prestar atencion a dichos simbolos. Indica una situacion de inminente riesgo, la cual, si no es evitada, causara la muerte o lesiones serias. Indica una situacion potencialmente peligrosa, la cual, si no es evitada, podria resultar en lesiones menores o moderadas. Indica una situac

This device provides additional protection from the risk of electrical shock. (Figure 1) FLOW RATE: This is the amount of water that passes through your wand. (Usually measured in G.P.M., gallons per minute.). IDLE MODE: This pertains to the time that the pressure washer is running without the trigger on the wand engaged to spray. You should never run this pressure washer for more than 5 minutes without pulling the trigger to relieve pressure. Running the pressure washer in this manner would voi

Operating unit with water supply shut off (without flow of water) will result in equipment damage. During shut-down, entire system including pump, hose and wand will remain under pressure. Do not attempt to remove hose/gun until pressure is relieved. 7 MAINTENANCE AND STORAGE TO AVOID ELECTRICAL SHOCK, ALWAYS DISCONNECT THE PLUG FROM THE ELECTRICAL SUPPLY BEFORE ANY MAINTENANCE IS STARTED. MAINTENANCE 1. WATER SCREEN: Inspect the water screen before attaching water supply. Clean water screen if

2. Increase frequency of oil changes if humidity or operating conditions are extreme. Every 160 Hours of Operation: 1. Check drive belt tension; adjust if necessary. (Refer to SERVICE INSTRUCTIONS in this manual.) 2. Inspect air lines and fittings for leaks; correct as necessary. 3. Check the alignment of the motor pulley to the flywheel. If necessary, align to within 1/32 inch on centerline. Each Year of Operation or if a Problem is Suspected: Check condition of air compressor pump intake and e

The pressure adjusting valve can be used to set approximate pressure between 10 and 125 P.S.I. (125 P.S.I. is the highest pressure this compressor will deliver). It is normal for the adjustable pressure valve to release air during operation. ALWAYS SET THE PRESSURE VALVE AT OR BELOW THE REQUIRED PRESSURE FOR THE ACCESSORY BEING USED BEFORE STARTING YOUR COMPRESSOR. FOR INFLATION OR OTHER USES REQUIRING ACCURATE PRESSURE, USE A PRESSURE GAUGE. INSTALLATION AND BREAK-IN PROCEDURES Location of the

NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. NEVER carry pressure washer with engine running, turn engine off and allow it to cool before carrying pressure washer. DO NOT let hoses come in contact with hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. NEVER pull water supply hose to move pressure

. . . . . .2 Important Safety Instructions. . . . .2–5 Specifications ...................6 CartonContents .................6 Assembly Instructions. . . . . . . . . . .6–7 Operating Instructions . . . . . . . . .8–13 Maintenance ................14–15 Storage ....................15–16 Troubleshooting Guide . . . . . . . .17–18 RepairWarranty ................20 IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before operat