If it contains the solvents listed do nized parts. You must either change the material you Read and follow the safety instructions provided on the label or safety data sheet for the material you are spraying. Use a respirator mask if there is a chance of tions . . . be sure that the respirator mask is suitable for y Electricity Your air compressor is powered by electricity. Like any other electrically powered device, if it is not used properly it may cause electrical shock. Always unplug the air

102D-3 Horsepower 3/4 SCFM @ 40 psig 3.0 SCFM @ 90 psig 2.2 Bore 1 3/4" Stroke 1 1/4" Volt/Hertz/Phase 120/60/1 Minimum Branch Circuit Requirement 15 AMPS *Fuse Type Quick Acting Tank Size 2 Gallon *A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit the air compressor is operated on. If the air compressor is connected to a circuit protected by fuses, use quick acting fuses. CAUTION indicates a potentially hazardous situation which, if

Read all the instructions before using the product. 2. To reduce the risk of injury, do not operate near children or animals. 3. Be thoroughly familiar with the controls. 4. Stay alert - watch what you are doing. 5. Do not operate the product when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all persons and animals. 7. Do not overreach or operate unit on unstable surface. Keep good footing and balance at all times. 8. Follow the maintenance instructions sp

observees, et notamment : WARNING ATTENTION 1. Read this manual carefully - know your equipment. Consider the applications, limitations, and the potential hazards specific to your unit. 2. Outlets with a third prong ground are required. Do not use without grounded prong. 3. Do not touch plug or outlet with wet hands. 4. Avoid accidental starts. Move switch on unit to “OFF” position before connecting or disconnecting cord to electrical outlets. 5. Water spray must never be directed towards any el

NOTE: Elbow fitting is not required, however, it provides strain relief for the hose. 2. Screw the hose into the open end of the elbow and tighten. Apply gasoline-resistant pipe compound to male threads. 3. Screw nozzle onto hose. NOTE: 1820R models are shipped with a vacuum breaker assembly (P/N 032701) consisting of a tee, pipe nipple and vacuum breaker. This assembly should be installed in the pump outlet before connecting the hose. 2-4 9312 Installation Direct Mount on Underground Tanks 1. S

4 — ENG HAZARD IMWHAT CAN HAPPEN PORTANT SAFETY INSHOW TO PREVENT IT TRUCTIONS WARNING • Spray directed at electrical outlets or switches, or objects connected to an electrical circuit, could result in a fatal • Unplug any electrically operated product before attempting to clean it. Direct spray away from electric outlets and switches. RISK OF electrical shock. ELECTRICAL SHOCK WARNING • Your washer operates at fluid pressures and velocities high enough to penetrate • Never place hands in front

SNC1002x4 Pull feeder shoe back into "locked" position. 6. NF2502X4, NB1252X4, NB2002X4, and SNC1002X4 Replace nose cover and latch into place. NBSNC2X4 Replace nose cover. 7. Reload fasteners into magazine. Refer to Feeder Magazine Latch 5. Using pliers remove fasteners. Loading the Tool section in this manual. PAGE 13 FASTENER JAM INSIDE MAGAZINE: SNC1002x4 Pull feeder shoe back into "locked" position. 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the maga

Install head valve piston set. Contact an *AWSC Sluggish operation. O-rings blown on head valve. Loose driver guide screws. Install head valve piston set. Contact an *AWSC Tighten screws. Air leak near bottom of tool. Bumper or piston o-rings worn. Replace bumper or piston assembly. Purchase a Bottom Repair Kit Tool does nothing. Air supply inadequate. O-rings failed on head valve piston set. Check PSI and CFM. Install head valve piston set. Contact an *AWSC Poor driver blade return. Dirty cylin